電纜直流耐壓測試儀是帶0.75倍電壓鎖存按鍵功能，并配有時間繼電器，該能在試驗中設置定時聲音報警，整個測試儀便于攜帶，操作方便，安全可靠，特別適用于電力檢修部門，發電廠以及電力檢修單位現場試驗。

電纜直流耐壓測試儀幾種升壓模式：

1、手動升壓模式

開機后，進入主菜單，旋動設置控制桿使光標指向“手動升壓"選項，點擊控制桿，進入手動模式參數設置界面，根據具體的試驗要求設置各項參數后，即可進入升壓界面。先按高壓通按鈕，紅燈亮起后，再旋動旋鈕，當電壓升至試驗電壓設定值，計時器開始計時，計時完畢后系統將自動降壓回零，然后彈出試驗記錄保存對話框，做出選擇后，該次試驗完畢；如果電壓未達到設定的試驗電壓值時，按下0.75UDC-1mA按鈕，則系統會自動降壓到當前電壓值的0.75倍，然后以設定的加壓時間倒計時，計時完畢后，系統自動降壓回零，然后彈出試驗記錄保存對話框，做出選擇后，該次試驗完畢。

2、自動升壓模式

開機后，進入主菜單，旋動設置控制桿使光標指向“自動升壓"選項，點擊控制桿，進入自動模式參數設置界面，根據具體的試驗要求設置各項參數后，即可進入升壓界面。此時，按下高壓通按鈕后，系統將開始自動升壓，升至試驗電壓設定值后，穩壓并開始計時，計時完畢后系統將會自動降壓回零，然后彈出試驗記錄保存對話框，做出選擇后，該次試驗完畢。

3、MOA升壓測試模式

開機后，進入主菜單，旋動設置控制桿使光標指向“MOA升壓"選項，點擊控制桿，進入自動模式參數設置界面，根據具體的試驗要求設置各項參數后，即可進入升壓界面。此時，按下高壓通按鈕后，系統將開始自動升壓，升至試驗電流設定值后，穩流并開始計時，計時完畢后系統自動降壓至原來電壓值的0.75倍，穩壓并重新開始計時，計時完畢后系統將會自動降壓回零，彈出試驗記錄保存對話框，做出選擇后，該次試驗完畢。試驗結束后，界面返回到主菜單界面，先用放電棒充分放電后，再關閉電源。

4、試驗完畢，關閉電源開關。

5、對于氧化鋅避雷器等小電容試品一般通過倍壓筒內部測壓電阻放電即可。而對電纜等大電容試品須安裝配套限流電阻，一般要待試品電壓自放電至試驗電壓的20%以下，再通過配套的放電棒進行放電。待試品充分放電后并掛好接地線，才允許進行高壓引線的拆除和更換接線工作。